How to Install Raised Access Foor / Raised Floor Installation

By: Changzhou HT Raised Floor Co.,Ltd  15-09-2016
Keywords: Installation, Raised Floor, Access Floor

Main Tools Include: Large push cutter, Infrared ray level instrument, Panel lifter, Screw driver, Wax wires, Level bar, Adz-eye Hammer, Nail, Pencil, Flexible rule, Pedestal adhesive, Tool bag, Broom, etc. Position Datum Point 1.Proper datum point can avoid the waste of room, the best choice is to set the intersection point of two walls which are rectangular as datum point. 2.If there is a ramp at door, or space for door to swing, the best datum point should be near door. 3.If designing or partition drawing has marked datum point,it can be considered as final. Notice: Datum line:A straight line paralleled to datum line,the longest distance between datum level and datum line is 600mm Datum level:It is a wall which owner requires to be installed with whole floor panel. Vertical:It is a straight line which is vertical to datum line.The largest distance between the vertical line and adjacent wall is 600mm. Raised Access Floor Installation: 1.At first,cleaning the ground. 2. Observe the layout of room, install infrared paralleled scanner, mark paralleled line on half waist of wall, then find the lowest and highest point, calculate average value from ground to floor surface(this average value equals to owner’s required installation height), calculate and adjust the pedestal height. 3.Choose a corner as start point, find a parallel on wall, tie two paralleled wax wire 595mm from wall,the wax wires are hard to break and extend, two wires must be vertically distributed. 4.While pulling the paralleled line, screw the four pedestals. After confirming the height and placing the first floor, stringers and pedestals must be fix with screws, use level bar to adjust floor, at last, lock nuts on the pedestals. 5.When the first floor is adjusted paralleled, vertically place two lines of floors in the direction of wax lines. Note: black glued edges between floors must be aligned and straight. 6.After vertically placing two rows of floors, find a direction(can not be vertically placed), paralleled place row by till the last row. Note: each edge should remain one row for final cutting and placing, while paving, floors can not be bended which may affect flatness . 7.After placing last row, iron angles in each corner may be firstly fixed, then cut all-round floor. Normally floor of last row should be cut, the cut side can be put on flat head pedestal directly, there is no need to use stringer for last row. Noted: iron angle should be paralleled to installed floor. Backing if iron angle should possess a support(flitch or angle bar). 8 .After fixing iron angle, precisely measure the size of floor,then cut and place it. If need placing plug, use cutting machine to open holes as per actual dimension. 9.After placing floor,check on time,adjust the parts which are not flat. Finally fill in gap when cutting with glass cement. 10.If the temperature difference between day and night at construction site is big,(high altitude,temperate area or arctic area), all the edges should remain 3mm gap. Check & Acceptance: After placing all floors, check whole project carefully and improve all the imperfect parts. 1.When walking on the floor,no noise,no movement and good stability. 2.Clean surface, clear pattern, mean color and joint, straight edged, no crack, no corner dropping, no lack of edge etc. 3.All materials of joint edge and dimensions should follow design requirement and construction regulation. Installation Video: https://www.youtube.com/watch?v=meBpJJM9BqI

Keywords: Access Floor, Installation, OA Floor, Raised Floor, Steel Panel,

Contact Changzhou HT Raised Floor Co.,Ltd

Email

Print this page

Share

Other products and services from Changzhou HT Raised Floor Co.,Ltd

Raised Floor Accessories Brush Grommet / Outlet Box / Close Cell Insulation from Changzhou HT Raised Floor Co.,Ltd thumbnail
15-09-2016

Raised Floor Accessories Brush Grommet / Outlet Box / Close Cell Insulation

Raised Floor Accessories Brush Grommet / Outlet Box / Close Cell Insulation


Tempered Glass Raised Flooring for Monitor and Decoration from Changzhou HT Raised Floor Co.,Ltd thumbnail
15-09-2016

Tempered Glass Raised Flooring for Monitor and Decoration

Tempered Glass Raised Flooring for Monitor and Decoration


Perforated Raised Floor System with Intelligent Automatic Temperature Control Machine from Changzhou HT Raised Floor Co.,Ltd thumbnail
15-09-2016

Perforated Raised Floor System with Intelligent Automatic Temperature Control Machine

Perforated Raised Floor System with Intelligent Automatic Temperature Control Machine


High Density Chipboard Core Woodcore Raised Access Floor System from Changzhou HT Raised Floor Co.,Ltd thumbnail
15-09-2016

High Density Chipboard Core Woodcore Raised Access Floor System

HT High Density Chipboard Core Woodcore Raised Access Floor System


High Strengthen Calcium Sulphate Raised Floor from Changzhou HT Raised Floor Co.,Ltd thumbnail
15-09-2016

High Strengthen Calcium Sulphate Raised Floor

High Strengthen Calcium Sulphate Raised Floor


Antistatic Raised Floor for Computer Room from Changzhou HT Raised Floor Co.,Ltd thumbnail
15-09-2016

Antistatic Raised Floor for Computer Room

Antistatic Raised Floor for Computer Room


Steel Raised Floor for General Office from Changzhou HT Raised Floor Co.,Ltd thumbnail
14-09-2016

Steel Raised Floor for General Office

Steel Raised Floor for General Office